manualshive.com logo in svg

Dell S4048T-ON, Руководство по настройке

Dell S4048T-ON - Устройство для сетевой конфигурации с Configuration Manual, доступным бесплатно для загрузки на manualshive.com. Руководство поможет настроить и оптимизировать работу устройства для максимальной производительности. Благодаря удобному manual пользователи смогут быстро освоить все особенности продукта.

Поделиться
Скачать
background image

Specifically:

•

Available CAM

 — the available number of CAM entries in the specified CAM partition for the specified line card or stack-unit port-

pipe.

•

Estimated CAM

 — the estimated number of CAM entries that the policy will consume when it is applied to an interface.

•

Status

 — indicates whether the specified policy-map can be completely applied to an interface in the port-pipe.

•

Allowed

 — indicates that the policy-map can be applied because the estimated number of CAM entries is less or equal to the 

available number of CAM entries. The number of interfaces in the port-pipe to which the policy-map can be applied is given in 

parentheses.

•

Exception

 — indicates that the number of CAM entries required to write the policy-map to the CAM is greater than the number of 

available CAM entries, and therefore the policy-map cannot be applied to an interface in the specified port-pipe.

NOTE: 

The 

show cam-usage

 command provides much of the same information as the 

test cam-usage

 command, but 

whether a policy-map can be successfully applied to an interface cannot be determined without first measuring how many CAM 
entries the policy-map would consume; the 

test cam-usage

 command is useful because it provides this measurement.

•

Verify that there are enough available CAM entries.

test cam-usage

Example of the 

test cam-usage

 Command

Dell# test cam-usage service-policy input pmap_l2  port-set 0  | port pipe

Port-pipe | CAM Partition | Available CAM | Estimated CAM | Status

=====================================================================

  0           L2ACL           500             200          Allowed(2)

Configuring Weights and ECN for WRED 

The WRED congestion avoidance functionality drops packets to prevent buffering resources from being consumed. Traffic is a mixture of 
various kinds of packets. The rate at which some types of packets arrive might be greater than others. In this case, the space on the buffer

 

and traffic manager (BTM) (ingress or egress) can be consumed by only one or few types of traffic, leaving no space for other types. You 
can apply a WRED profile to a policy-map so that the specified traffic can be prevented from consuming too much of the BTM resources.

WRED drops packets when the average queue length exceeds the configured threshold value to signify congestion. ECN is a capability that 
enhances WRED by marking the packets instead of causing WRED to drop them when the threshold value is exceeded. If you configure 
ECN for WRED, devices employ ECN to mark the packets and reduce the rate of sending packets in a congested network.

In a best-effort network topology, data packets are transmitted in a manner in which latency or throughput is not maintained to be at an 
effective level. Packets are dropped when the network experiences a large traffic load. This best-effort network deployment is not suitable 
for applications that are time-sensitive, such as video on demand (VoD) or voice over IP (VoIP) applications. In such cases, you can use 
ECN in conjunction with WRED to resolve the dropping of packets under congested conditions.

Using ECN, the packets are marked for transmission at a later time after the network recovers from the heavy traffic state to an optimal 
load. In this manner, enhanced performance and throughput are achieved. Also, the devices can respond to congestion before a queue 
overflows and packets are dropped, enabling improved queue management.

When a packet reaches the device with ECN enabled for WRED, the average queue size is computed. To measure the average queue size, 
a weight factor is used. This weight factor is user-configurable. You can use the 

wred weight number

 command to configure the 

weight for the WRED average queue size. The mark probability value is the number of packets dropped when the average queue size 
reaches the maximum threshold value.

The weight factor is set to zero by default, which causes the same behavior as dropping of packets by WRED during network loads or also 
called instantaneous ECN marking. In a topology in which congestion of the network varies over time, you can specify a weight to enable a 
smooth, seamless averaging of packets to handle the sudden overload of packets based on the previous time sampling performed. You can 
specify the weight parameter for front-end and backplane ports separately in the range of 0 through 15.

Quality of Service (QoS)

751

Содержание S4048T-ON



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S4048T-ON

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Бренд: Baracoda Страницы: 42
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Бренд: Jetter Страницы: 35
Laird OL 4503 Specification And User Manual preview
OL 4503
Бренд: Laird Страницы: 36
Lanner NCA-2510 Installation Manual preview
NCA-2510
Бренд: Lanner Страницы: 2
Abocom HomePlug AV Ethernet Bridge PLE0200 Quick Install preview
HomePlug AV Ethernet Bridge PLE0200
Бренд: Abocom Страницы: 2
NETGEAR FS605 v3 Installation Manual preview
FS605 v3
Бренд: NETGEAR Страницы: 84
Selta Alyseo 106 User Manual preview
Alyseo 106
Бренд: Selta Страницы: 83
Aethra AS1241 Technical Specifications preview
AS1241
Бренд: Aethra Страницы: 2
B&B Electronics EIP308 Product Information preview
EIP308
Бренд: B&B Electronics Страницы: 2
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Бренд: Element14 Страницы: 2
Cabletron Systems SmartSwitch 8-slot User'S Reference Manual preview
SmartSwitch 8-slot
Бренд: Cabletron Systems Страницы: 150
ZALMAN CNPS7000C Series User Manual preview
CNPS7000C Series
Бренд: ZALMAN Страницы: 8
Eurotech Zypad WL15 Series Quick Start preview
Zypad WL15 Series
Бренд: Eurotech Страницы: 2
Perle IOLAN MDC User Manual preview
IOLAN MDC
Бренд: Perle Страницы: 491
B&B Electronics Elinx EIR510 Series Quick Start Manual preview
Elinx EIR510 Series
Бренд: B&B Electronics Страницы: 2
Casablanca W-500 Technical Bulletin preview
W-500
Бренд: Casablanca Страницы: 13
Planet WNAP-7335 Quick Installation Manual preview
WNAP-7335
Бренд: Planet Страницы: 2
TDK Powereta iQP Series Product Brief preview
Powereta iQP Series
Бренд: TDK Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды