Dell PowerConnect J-8216 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 270

Dell PowerConnect J-8216 Скачать руководство пользователя страница 39

Table 11: LCD Panel Menu Options for the J-EX8200 Switch

(continued)

Description

Menu

The Maintenance menu has the following options:

•

SYSTEM HALT?—Choose one of the following:

•

Press

Enter

to halt the master RE module in a J-EX8216 switch. Press

Enter

again to confirm the halt.

In a redundant configuration, the backup SRE or RE module takes over mastership when the master SRE
or RE module is halted. To completely halt the switch, use the

request system halt other-routing-engine

CLI command to halt the backup SRE or RE module before halting the master SRE or RE module. Press

Enter

on your management device or power cycle the switch to bring the switch back up.

•

Press

Menu

to go to the next option in the Maintenance menu.

•

SYSTEM REBOOT?—Choose one of the following:

•

Press

Enter

to reboot the master SRE or RE module. Press

Enter

again to confirm the reboot.

•

Press

Menu

to go to the next option in the Maintenance menu.

•

LOAD RESCUE?—Choose one of the following:

•

Press

Enter

to roll back the switch to the previous valid configuration. Press

Enter

again to confirm the

rollback.

•

Press

Menu

to go to the next option in the Maintenance menu.

•

FACTORY DEFAULT?—Choose one of the following:

•

Press

Enter

to restore the switch to the factory default configuration. Press

Enter

again to confirm the

restoration. The LCD flashes a success or failure message and returns to the Idle menu.

•

Press

Menu

to go to the next option in the Maintenance menu.

•

ENTER EZSETUP?—Choose one of the following:

•

Press

Enter

to launch EZSetup. Press

Enter

again to confirm the launch.

EZSetup configures DHCP and enables the J-Web user interface on the switch. The LCD flashes a success
or failure message for approximately 10 seconds and returns to the Idle menu.

•

Press

Menu

to go to the next option in the Maintenance menu.

NOTE: You can use the EZSetup option only if the switch is in the factory default configuration.

•

EXIT MAINT MENU?—Choose one of the following:

•

Press

Enter

to exit the Maintenance menu.

•

Press

Menu

to return to the SYSTEM HALT option.

If you do not want users to use Maintenance menu options, disable the entire menu or individual menu options.
For instructions, see the

Dell PowerConnect J-Series Ethernet Switch Complete Software Guide for Junos OS

at

http://www.support.dell.com/manuals

Maintenance

You can view the information about the LCD panel in J-EX8200 switches by executing
the command

show chassis hardware

. It shows the version, part number, serial number,

and description of the LCD panel.

Related

Documentation

Chassis Status LEDs in a J-EX8200 Switch on page 24

•

•

Field-Replaceable Units in a J-EX8216 Switch on page 25

•

Connecting and Configuring a J-EX Series Switch (CLI Procedure) on page 144

•

Connecting and Configuring a J-EX Series Switch (J-Web Procedure) on page 146

23

Chapter 2: Component Descriptions

«
...
37
38
39
40
41
...
»

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды