Dell PowerConnect J-8216 Скачать руководство пользователя страница 150

Страница: 150 / 270

For connecting a management device to the console port, see “Connecting a J-EX
Series Switch to a Management Console” on page 136. For connecting a management
device to the management port, see “Connecting a J-EX Series Switch to a Network
for Out-of-Band Management” on page 135.

To power on the switch:

Attach the ESD grounding strap to your bare wrist and connect the strap to the ESD
point on the chassis.

Connect the external management device to the master SRE or master RE module's
management (MGMT) port.

Turn on the power to the external management device.

Ensure that the power supplies are fully inserted in the chassis and that each of their
handles is flush against the faceplate.

Ensure that the source power cord is inserted securely into the appliance inlet for each
AC power supply.

Switch on the site circuit breakers.

Flip a power supply’s

Enable

switch to the on position (ON). See Figure 60 on page 134.

Observe the power supply faceplate LEDs. If the power supply is installed correctly
and functioning normally, the

INPUT OK

IN OK

and

OUTPUT OK

OUT OK

LEDs light

and remain constantly lit. The

FAIL

LED does not light.

Figure 60: Flip the Enable Switch to the ON position

Repeat Step 7 for the remaining power supplies installed in the switch.

On the external management device, monitor the startup process to ensure that the
system boots properly.

134

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды