Dell PowerConnect J-8216 Скачать руководство пользователя страница 59

Страница: 59 / 270

Figure 26: AC Power Supply LEDs on a J-EX8200 Switch

Table 25 on page 43 describes the LEDs on an AC power supply in a J-EX8200 switch.

Table 25: Power Supply LEDs on J-EX8200 Switches

Description

State

LED

Indicates one of the following:

•

Power supply is disconnected from AC power feed.

•

AC power input voltage is not within normal
operating range.

•

No AC power input.

Unlit

INPUT OK

•

AC power input voltage is high line (200–240 VAC).

Green

•

AC power input voltage is low line (100–120 VAC).

Yellow

NOTE: This LED state
applies only to 2000 W AC
power supplies.

Indicates one of the following:

•

DC output voltage is not within normal operating
range.

•

Power supply is not supplying DC power correctly.

Unlit

OUTPUT OK

•

DC power output is within normal operating range.

Green

•

Power supply has been disabled internally by the
system.

Yellow

•

Power supply is functioning normally.

Unlit

FAIL

•

On steadily—Power supply has failed.

•

Blinking—Demand for output power exceeds the
supply.

Yellow

Chapter 2: Component Descriptions

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды