Dell PowerConnect J-8216 Скачать руководство пользователя страница 230

Страница: 230 / 270

Varning!

Läs installationsanvisningarna innan du kopplar systemet till dess

strömförsörjningsenhet.

Documentation

General Safety Guidelines and Warnings for J-EX Series Switches on page 201

•

Laser and LED Safety Guidelines and Warnings for J-EX Series Switches on page 207

•

Grounded Equipment Warning for J-EX Series Switches on page 219

•

Connecting AC Power to a J-EX8200 Switch on page 131

Chassis Lifting Guidelines for J-EX8200 Switches

The weight of a fully loaded J-EX8216 switch is approximately 486 lb (220 kg). Observe
the following guidelines for lifting and moving the switch:

WARNING:

Because of the J-EX8216 switch’s size and weight, we require the

use of a mechanical lift to install the J-EX8216 switch in a rack or cabinet or
to move the switch from one location to another.

•

Before moving the switch to a site, ensure that the site meets the power, environmental,
and clearance requirements specified in the “Site Preparation Checklist for a J-EX8200
Switch” on page 63.

•

Before lifting or moving the switch, disconnect all external cables and wires.

•

Do not grasp the switch by the blue panel at the top front of the chassis. Doing so can
cause the panel to detach from the switch.

Documentation

General Safety Guidelines and Warnings for J-EX Series Switches on page 201

•

Installation Instructions Warning for J-EX Series Switches on page 213

•

Mounting a J-EX8216 Switch on a Rack or Cabinet on page 108

Ramp Warning for J-EX Series Switches

WARNING:

When installing the switch, do not use a ramp inclined at more

than 10 degrees.

Waarschuwing

Gebruik een oprijplaat niet onder een hoek van meer dan 10

graden.

Varoitus

Älä käytä sellaista kaltevaa pintaa, jonka kaltevuus ylittää 10 astetta.

Attention

Ne pas utiliser une rampe dont l'inclinaison est supérieure à 10

degrés.

214

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды