manualshive.com logo in svg

Dell PowerConnect J-8216, Руководство по оборудованию

Поделиться
Скачать
Dell PowerConnect J-8216 Скачать руководство пользователя страница 45

Management Port LEDs in J-EX8200 Switches

The management port on J-EX8200 switches has two LEDs that indicate link/activity
and port status (see Figure 12 on page 29). The management port is set to full-duplex
and the speed is set to 100 Mbps.

Figure 12: LEDs on the Management Port on a J-EX8200 Switch

Table 15 on page 29 describes the Link/Activity LED.

Table 15: Link/Activity LED on the Management Port on J-EX8200 Switches

State and Description

Color

LED

•

Blinking—The port and the link are active, and there is link
activity.

•

On steadily—The port and the link are active, but there is no
link activity.

•

Off—The port is not active.

Green

Link/Activity

Table 16 on page 29 describes the Status LED (administrative status).

Table 16: Status LED on the Management Port on J-EX8200 Switches

State and Description

Color

LED

•

On steadily—Administrative status is enabled.

•

Off—Administrative status is disabled.

Green

Status

Related

Documentation

See Routing Engine (RE) Module in a J-EX8216 Switch on page 26 for port location.

•

•

Connecting a J-EX Series Switch to a Network for Out-of-Band Management on page 135

Switch Fabric (SF) Modules in a J-EX8216 Switch

The Switch Fabric (SF) modules provide switching functionality to a J-EX8216 switch.
See Figure 13 on page 30.

29

Chapter 2: Component Descriptions

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды