Dell PowerConnect J-8216 Скачать руководство пользователя страница 44

Страница: 44 / 270

Figure 11: RE Module LEDs in a J-EX8216 Switch

Table 14 on page 28 describes these LEDs, their colors and states, and the status they
indicate.

Table 14: RE Module LEDs in a J-EX8216 Switch

State and Description

Color

LED Label (Description)

RE module is powered on.

Green

ON (Power On)

RE module is powered off.

Unlit

•

On steadily—RE module is operating normally.

•

Blinking—RE module is booting.

Green

ST (Status)

•

On steadily—RE module has failed.

Yellow

RE module is offline.

Unlit

•

On steadily—RE module is the master.

•

Blinking—RE module is in standby mode.

Green

MS (Master)

RE module is powered off.

Unlit

•

On steadily—Switch fabric in the Switch Fabric (SF) modules
is operating normally.

Green

SF (Switch Fabric)

Switch fabric in one or more SF modules has failed.

Yellow

RE module is powered off.

Unlit

Documentation

Routing Engine (RE) Module in a J-EX8216 Switch on page 26

•

Installing an RE Module in a J-EX8216 Switch on page 118

•

Removing an RE Module from a J-EX8216 Switch on page 163

•

Taking the RE Module Offline in a J-EX8216 Switch on page 161

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды