manualshive.com logo in svg

Dell PowerConnect J-8216, Руководство по оборудованию

Поделиться
Скачать
Dell PowerConnect J-8216 Скачать руководство пользователя страница 48

Table 17: SF Module LEDs in a J-EX8216 Switch

State and Description

Color

LED (Description)

•

On steadily—SF module is operating normally.

•

Blinking—the SF module is in standby mode.

Green

ST (Status)

SF module has failed.

Yellow

SF module is offline.

Unlit

On steadily—Switch fabric in SF module is operating normally.

Blinking—Switch fabric in SF module is offline.

Green

SF (Switch Fabric)

On steadily—Switch fabric in SF module has failed.

Yellow

SF module is powered off.

Unlit

Related

Documentation

Switch Fabric (SF) Modules in a J-EX8216 Switch on page 29

•

•

Installing an SF Module in a J-EX8216 Switch on page 120

•

Removing an SF Module from a J-EX8216 Switch on page 165

•

Taking the SF Module Offline in a J-EX8216 Switch on page 164

8-port SFP+ Line Card in a J-EX8200 Switch

The line cards in J-EX8200 switches combine a Packet Forwarding Engine and Ethernet
interfaces on a single assembly. They are field-replaceable units (FRUs) that can be
installed in the line card slots on the front of the switch chassis. The line cards are
hot-insertable and hot-removable: You can remove and replace them without powering
off the switch or disrupting switch functions.

J-EX8200 switches use the following types of line cards:

•

8-port SFP+ line card

•

48-port SFP line card

•

48-port RJ-45 line card

You can use any combination of line cards in a J-EX8200 switch.

The 8-port SFP+ line card for J-EX8200 switches (see Figure 15 on page 33) has eight
10-gigabit SFP+ ports on the faceplate in which you can install SFP+ transceivers. The
line card is shipped with dust covers preinstalled in the ports. Each port has two LEDs.
See “Network Port LEDs in a J-EX8200 Switch” on page 36.

32

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды