Dell PowerConnect J-8216 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 270

Dell PowerConnect J-8216 Скачать руководство пользователя страница 122

13.

Use 4 mounting screws appropriate for your rack—plus washers if you installed cage
nuts—to attach the right rear bracket to the rack.

14.

Connect the right front and rear brackets (see Figure 39 on page 105):

a.

Insert 6 of the screws provided with the mounting brackets into the overlapping
bracket holes.

b.

Hand tighten the screws fully (to 12–16 in.-lb torque) using a number 2 Phillips
screwdriver.

Figure 40: Adjustable Mounting Brackets Installed in a Four-Post Rack
(J-EX8216 Switch)

Related

Documentation

Mounting a J-EX8216 Switch on a Rack or Cabinet on page 108

•

Installing the Power Cord Tray in a Rack or Cabinet for a J-EX8200 Switch

The power cord tray is supplied with all J-EX8200 switches. The power cord tray is
optional for four-post rack or cabinet installation. (The remainder of this topic uses “rack”
to mean “rack or cabinet.”)

NOTE:

The J-EX8216 switch can be installed only in a four-post rack.

Installation in a two-post rack is not supported.

The power cord tray provides a place to organize and tie down the power cords for the
power supplies.

106

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

«
...
120
121
122
123
124
...
»

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды