Dell PowerConnect J-8216 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 270

Dell PowerConnect J-8216 Скачать руководство пользователя страница 82

Table 31: Site Electrical Wiring Guidelines

(continued)

Guidelines

Site Wiring Factor

If your site is susceptible to problems with electromagnetic
compatibility (EMC), particularly from lightning or radio
transmitters, seek expert advice.

Some of the problems caused by strong sources of
electromagnetic interference (EMI) are:

•

Destruction of the signal drivers and receivers in the switch

•

Electrical hazards as a result of power surges conducted
over the lines into the equipment

Electromagnetic compatibility

Related

Documentation

General Safety Guidelines and Warnings for J-EX Series Switches on page 201

•

•

General Electrical Safety Guidelines and Warnings for J-EX Series Switches on page 229

•

Prevention of Electrostatic Discharge Damage on J-EX Series Switches on page 230

•

AC Power Supply in a J-EX8200 Switch on page 39

Environmental Requirements and Specifications for J-EX Series Switches

The switch must be installed in a rack or cabinet housed in a dry, clean, well-ventilated,
and temperature-controlled environment.

Ensure that these environmental guidelines are followed:

•

The site must be as dust-free as possible, because dust can clog air intake vents and
filters, reducing the efficiency of the switch cooling system.

•

Maintain ambient airflow for normal switch operation. If the airflow is blocked or
restricted, or if the intake air is too warm, the switch might overheat, leading to the
switch temperature monitor shutting down the switch to protect the hardware
components.

Table 32 on page 66 provides the required environmental conditions for normal switch
operation.

Table 32: J-EX Series Switch Environmental Tolerances

Tolerance

Description

No performance degradation to 10,000 feet (3048 meters)

Altitude

Normal operation ensured in relative humidity range of 10% through
85%, noncondensing

Relative humidity

Normal operation ensured in temperature range of 32° F through
104° F (0° C through 40° C)

Temperature

66

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

«
...
80
81
82
83
84
...
»

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды