Dell PowerConnect J-8216 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 270

Dell PowerConnect J-8216 Скачать руководство пользователя страница 156

8.

To disable flow control on the modem, type

at&k0

at the prompt. Press Enter.

9.

To set the fixed serial port speed on the modem, type

at&b1

at the prompt. Press

Enter.

NOTE:

You must set the serial port to the fixed speed so that the modem

will not adjust the serial port speed to the negotiated line speed.

10.

To save the new modem settings, type

at&w0

at the prompt. Press Enter.

The modem sends an OK message. The modem is now ready to be connected to the
switch.

Connecting the Modem to the Console Port

The console port on every J-EX Series switch accepts a cable with an RJ-45 connector.
Figure 66 on page 140 shows the RJ-45 connector of the Ethernet cable supplied with the
switch.

Figure 66: Ethernet Cable Connector

NOTE:

If your laptop or PC does not have a DB-9 male connector pin and you

want to connect your laptop or PC directly to the switch, use a combination
of the RJ-45 to DB-9 female adapter supplied with the switch and a USB to
DB-9 male adapter. You must provide the USB to DB-9 male adapter.

NOTE:

Most modems have an RS-232 DB-25 connector. You must separately

purchase an adapter to connect your modem to the RJ-45 to DB-9 adapter
and Ethernet cable supplied with the switch.

To connect a modem to the console port:

1.

Turn off power to the switch.

2.

Turn off power to the modem.

3.

Connect one end of the cable to the console port (labeled

CON

or

CONSOLE

) on the

switch.

For the location of the console port, see “Routing Engine (RE) Module in a J-EX8216
Switch” on page 26.

4.

Connect the other end of the cable to the RJ-45 to DB-9 serial port adapter supplied
with your switch.

140

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

«
...
154
155
156
157
158
...
»

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды