manualshive.com logo in svg

Dell PowerConnect J-8216, Руководство по оборудованию

Поделиться
Скачать
Dell PowerConnect J-8216 Скачать руководство пользователя страница 162

Connecting and Configuring a J-EX Series Switch (J-Web Procedure)

There are two ways to connect and configure a J-EX Series switch: one method is through
the console using the CLI and the other is using the J-Web interface. This topic describes
the J-Web procedure.

NOTE:

Before you begin the configuration, enable a DHCP client on the

management PC you will connect to the switch so that the switch can obtain
an IP address dynamically.

NOTE:

Read the following steps before you begin the configuration. You

must complete the initial configuration using EZSetup within 10 minutes. The
switch exits EZSetup after 10 minutes and reverts to the factory default
configuration, and the PC loses connectivity to the switch. The LCD displays
a count-down timer when the switch is in initial setup mode.

To connect and configure the switch using the J-Web interface:

1.

To transition the switch into initial setup mode, use the

Menu

and

Enter

buttons located

to the right of the LCD panel (see Figure 67 on page 146):

Figure 67: LCD Panel in a J-EX8200 Switch

a. Press the

Menu

button until you see

MAINTENANCE MENU

. Then press the

Enter

button.

b. Press

Menu

until you see

ENTER EZSetup

. Then press

Enter

.

If EZSetup does not appear as an option in the menu, select Factory Default to
return the switch to the factory default configuration. EZSetup is displayed in the
menu only when the switch is set to the factory default configuration.

c. Press

Enter

to confirm setup and continue with EZSetup.

2.

Connect the Ethernet cable from the Ethernet port on the PC to the port labeled

MGMT

on the Routing Engine (RE) module in slot RE0.

This port is configured as the DHCP server with the default IP address,

192.168.1.1

. The

switch can assign an IP address to the management PC in the IP address range

192.168.1.2

through

192.168.1.253

.

3.

From the PC, open a Web browser, type

http://192.168.1.1

in the address field, and

press Enter.

146

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды