Dell Alienware Aurora R4 Скачать руководство пользователя страница 57

Страница: 57 / 162

Graphics Card

Graphics Card

WARNING:

Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on
page 13. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.

The system board of your computer is equipped with two PCI-Express x16

connectors to install graphic card(s). To locate the PCI-Express x16 connectors

on the system board, see "System-Board Components" on page 20.

Prerequisites

Remove the left side-panel. See "Removing the Left Side-Panel" on

page 25.

Open the PCI shroud. See "Opening the PCI Shroud" on page 45.

Removing the Graphics Card

Locate the graphics card (PCI-Express x16 card) on the system board. See

"System-Board Components" on page 20.

NOTE:

The location of the power-cable connectors on your graphics card may

vary.

Press the releasing clips on the power-cable connectors and disconnect the

power cables from the graphics card.

Remove the screws that secure the graphics card to the chassis.

Press and hold the securing tab on the card connector, grasp the card by its

top corners, and then ease the card out of the card connector.

book.book Page 57 Wednesday, May 16, 2012 2:37 PM

Содержание Alienware Aurora R4



































































































































































Результаты поиска

Содержание Alienware Aurora R4

Отзывы:

Похожие инструкции для Alienware Aurora R4

Бренды по названию

Популярные бренды

Dell Alienware Aurora R4, Руководство пользователя

Результаты поиска

Содержание Alienware Aurora R4

Отзывы:

Похожие инструкции для Alienware Aurora R4

Бренды по названию

Популярные бренды