Dell Alienware Aurora R4 Скачать руководство пользователя страница 150

Страница: 150 / 162

150

System Setup Utility

tRCD

Displays timing of RAS to CAS delay

(editable in Manual Mode).

tRP

Displays timing of RAS Precharge

(editable in Manual Mode).

tRAS

Displays timing of Row Address Strobe

(editable in Manual Mode).

tRFC

Displays timing of Refresh to

Archive/Refresh cycle time (editable in

Manual Mode).

tWR

Displays timing of Write Recover

(editable in Manual Mode).

tWTR

Displays Write to Read Delay (editable in

Manual Mode).

tRRD

Displays RAS to RAS delay (editable in

Manual Mode).

tRTP

Displays Read to Precharge Command

Delay (editable in Manual Mode).

tFAW

Displays the Four Activate Window

(editable in Manual Mode).

tWCL

Displays the Write CAS Latency

(editable in Manual Mode).

tCKE

Displays the Minimum CKE High and

Low Pulse Width (editable in Manual

Mode).

tRTL

Displays the Round Trip Latency

(editable in Manual Mode).

tXP

Displays the XP value (editable in

Manual Mode).

CPU Power Management Configuration

Intel Turbo Boost

If enabled, allows processor to run at

faster frequencies than marked.

Long duration power limit

Allows you to change the long duration

power limit.

book.book Page 150 Wednesday, May 16, 2012 2:37 PM

Содержание Alienware Aurora R4



































































































































































Результаты поиска

Содержание Alienware Aurora R4

Отзывы:

Dell Alienware Aurora R4, Руководство пользователя, Страница: 150 / 162

Результаты поиска

Содержание Alienware Aurora R4

Отзывы: