Deliberant FWBD0501 Скачать руководство пользователя страница 42

Страница: 42 / 67

User’s

Guide

deliberant

Page

Wireless

Mode:

iPoll

Station

The

iPoll Station

is a wireless client mode which can connect to the iPoll Access Points.

Figure 37 – iPoll Station's Wireless Settings

Basic

Settings

Use this section to setup basic operating settings of the iPoll Station radio.

iPoll Access Point and iPoll Station will operate in 802.11n IEEE mode only.

SSID

– specify the SSID of the wireless network device manually, or use

Scan

functionality.

Scan

– click this button to scan for surrounding iPoll Access Points. Found network SSID’s will be

available in drop down menu.

Channel width

– The default channel bandwidth for 802.11 N radio is 20/40MHz. The 802.11n allow

channel bonding in such way the total channel width becomes 40MHz.

Security

Settings

Both sides (iPoll Access Point and iPoll Station) of the link must have the same security
settings.

The APC device working, in iPoll Station wireless mode, supports authentication/encryption methods
listed below:

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды

Deliberant FWBD0501, Руководство пользователя

Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды