Deliberant FWBD0501 Скачать руководство пользователя страница 29

Страница: 29 / 67

User’s

Guide

deliberant

Page

Figure 16 – Router LAN Settings

IP address

– specify the IP address of the device LAN interface.

Subnet mask

– specify the subnet mask of the device LAN interface.

LAN

DHCP

Settings

DHCP mode

– choose disabled to disable DHCP on LAN interface.

Figure 17 – Router LAN Settings: DHCP Disabled

DHCP mode

– choose relay to enable DHCP relay. The DHCP relay forwards DHCP messages

between subnets with different sublayer broadcast domains.

Figure 18 – Router LAN Settings: DHCP Relay

DHCP mode

– choose server to enable DHCP server on LAN interface.

Figure 19 – Router LAN Settings: DHCP Server

IP address from

– specify the starting IP address of the DHCP address pool.

IP address to

– specify the ending IP address of DHCP address pool.

Subnet mask

– specify the subnet mask.

Default gateway

– specify DHCP gateway IP address.

Lease time

– specify the expiration time in seconds for the IP address assigned by the DHCP server.

DNS server

– specify the DNS server IP address.

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды

Deliberant FWBD0501, Руководство пользователя

Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды