Deliberant FWBD0501 Скачать руководство пользователя страница 65

Страница: 65 / 67

User’s

Guide

deliberant

Page

RADIUS

Attributes

The following RADIUS attributes and messages are supported by the DLB APC.

General

Attributes

Attribute

Description

User-name (1)

Full username as entered by the user.

User-Password (2)

Used for UAM as alternative to CHAP-Password and CHAP-Challenge.

CHAP-Password (3)

Used for UAM CHAP Authentication

CHAP-Challenge (60)

Used for UAM CHAP Authentication

EAP-Message (79)

Used for WPA Authentication

NAS-IP-Address (4)

IP address of Chilli (set by the

nasip

radiuslisten

option, and

otherwise "0.0.0.0")

Service-Type (6)

Set to Login (1) for normal authentication requests. The Access-Accept
message from the
radius server for configuration management messages must also be
set to Administrative-User.

Framed-IP-Address (8)

IP address of the user, which is configurable during MAC
authentication in the Access-Accept.

Filter-ID (11)

Filter ID pass on to scripts possibly.

Reply-Message (18)

Reason of reject if present.

State (24)

Sent to chilli in Access-Accept or Access-Challenge. Used
transparently in subsequent Access-Request.

Class (25)

Copied transparently by chilli from Access-Accept to Accounting-
Request.

Session-Timeout (27)

Logout once session timeout is reached (seconds)

Idle-Timeout (28)

Logout once idle timeout is reached (seconds)

alled-Station-ID (30)

Set to the nasmac option or the MAC address of chilli.

Calling-Station-ID (31)

MAC address of client

NAS-Identifier (32)

Set to radiusnasid option if present.

Acct-Status-Type (40)

1=Start, 2=Stop, 3=Interim-Update

Acct-Input-Octets (42)

Number of octets received from client.

Acct-Output-Octets (43)

Number of octets transmitted to client.

Acct-Session-ID (44)

Unique ID to link Access-Request and Accounting-Request messages.

Acct-Session-Time (46)

Session duration in seconds.

Acct-Input-Packets (47)

Number of packets received from client.

Acct-Output-Packets (48)

Number of packets transmitted to client.

Acct-Terminate-Cause (49)

1=User-Request, 2=Lost-Carrier, 4=Idle-Timeout, 5=Session-Timeout,
11=NAS-Reboot

Acct-Input-Gigawords (52)

Number of times the Acct-Input-Octets counter has wrapped around.

Acct-Output-Gigawords (53)

Number of times the Acct-Output-Octets counter has wrapped around.

NAS-Port-Type (61)

19=Wireless-IEEE-802.11

Message-Authenticator (80)

Is always included in Access-Request. If present in Access-Accept,
Access-Challenge or

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды

Deliberant FWBD0501, Руководство пользователя

Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды