Deliberant FWBD0501 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 67

background image

User’s

Guide

deliberant

Page

31

Wireless

Mode:

Access

Point

(auto

WDS)

Use Basic Wireless Settings to setup radio interface of the device.

Figure 21 – Access Point Wireless Settings

Basic

Wireless

Settings

SSID

– specify the SSID of the wireless network device.

Broadcast SSID

– enables or disables the broadcasting of the SSID for AP.

IEEE mode

– specify the wireless network mode.

Channel width

– The default channel bandwidth for 802.11 radio is 20MHz. The 802.11n allow

channel bonding in such way the total channel width becomes 40MHz.

Channel

– displays the channel at which the AP is operating, or indicates that autochannel function is

used.

Channel list

– select the channel(s) at which the AP unit will operate. If more than one channel is

selected, then autochannel feature will be enabled. Automatic channel selection allows AP to select a
channel which is not used by any other wireless device or, if there are no free channels available - to
select a channel which is least occupied. The table displays detailed information about each channel:

«
...
29
30
31
32
33
...
»

Содержание FWBD0501




































































Отзывы:

Нет отзывов

Похожие инструкции для FWBD0501

Бренд: Pakedge Страницы: 7

Бренд: Pakedge Страницы: 4

Бренд: LevelOne Страницы: 14

Бренд: Shiro Страницы: 83

Бренд: Alfa Network Страницы: 226

Бренд: Z-Com Страницы: 23

Бренд: NETGEAR Страницы: 2

Pepwave Surf SOHO

Бренд: peplink Страницы: 151

Бренд: Digisol Страницы: 29

WGR612 - 54 Mbps Wireless Router

Бренд: NETGEAR Страницы: 2

Бренд: Niveo Professional Страницы: 35

Бренд: Billionton Страницы: 43

Бренд: Advantech Страницы: 50

WISE-3200 Series

Бренд: Advantech Страницы: 56

Бренд: SingTel Страницы: 13

WatchGuard AP327X O-105E

Бренд: Watchguard Страницы: 32

Бренд: ELTEX Страницы: 22

Бренд: Packedge Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды