Deliberant FWBD0501 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 67

background image

deliberant

Page

3

List of additional approval antenna:

Omni Directional (fiberglass pole) EXTRALINK OMNI 12dBi

Omni Directional (Rubber Duck Omni Antenna (RPSMA)) 3dBi

Sector FWA-5 16dBi

Panel FWA-24 8dBi

Panel FWA18 14dBi

Dish RocketDish 24dBi

Antenna Installation Warning:

1, It is installer’s responsibility to ensure that when using the authorized antennas in the United States
(Or where FCC rules only);

2, only those antennas certified with the product are used;

3, the use of any antenna other than those certified with the product is expressly forbidden in
accordance to FCC rules CFR 47 part 15.204;

4, The Installer should configure the output power level of antenna, according to country regulations
and per antenna type;

5, Professional installation is required of equipment with connectors to ensure compliance with health
and safety issues.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be installed such
that 100 cm may be maintained between the antenna and users. This final and product must be
labeled in a visible area with the following: Contains FCC ID: “UB8-FWBD0501’’.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this module.

The end user manual shall include all required regulatory information/Warning as show in this manual.

RSS (Category I Equipment):

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired
operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.

«
1
2
3
4
5
...
»

Содержание FWBD0501




































































Отзывы:

Нет отзывов

Похожие инструкции для FWBD0501

Бренд: T-Mobile Страницы: 4

EN-SLX 9640-24S-12C

Бренд: Extreme Networks Страницы: 113

Бренд: RAK Страницы: 19

Бренд: Hamlet Страницы: 10

Бренд: Linksys Страницы: 138

Бренд: Zte Страницы: 29

Бренд: Xact Страницы: 16

Бренд: Accton Technology Страницы: 34

Бренд: Accton Technology Страницы: 42

Бренд: Air Live Страницы: 171

Бренд: Air Live Страницы: 161

Бренд: Ubiquiti Страницы: 14

Бренд: LongSung Technology Страницы: 32

Бренд: NETGEAR Страницы: 185

Бренд: 2N Страницы: 82

Бренд: E-Lins Страницы: 6

Бренд: Sapido Страницы: 106

Бренд: Novatel Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды