Deliberant FWBD0501 Скачать руководство пользователя страница 49

Страница: 49 / 67

User’s

Guide

deliberant

Page

System

alerts

The device is able to send external alerts when there are system errors. The alerts can be sent via
SNMP Traps or/and SMTP notifications.

Figure 48 – Device Alerts

Enable alerts

– select to enable alert notifications on the system.

System check interval, s

– specify interval in seconds at which the device will send notifications of

unexpected system behavior.

System alerts:

Wireless link status change

– system will send notification on Wireless link status change.

Ethernet link status change

– system will send notification on Ethernet link status change.

RSSI level lower than

– system will send notification when RSSI reach value lower than specified.

Default: 25

Noise level greater than

– system will send notification when signal noise will reach value greater

than specified. Default: -60 dBm.

RX drop greater than

– system will send notification when percent of RX dropped packets become

higher than specified value. Default: 250 packets per seconds.

TX retry greater than

– system will send notification when percent of TX retries becomes higher than

specified value. Default: 250 packets per seconds.

Device reboot

– system will send notification about unexpected or administrator initiated device

reboot.

Figure 49 – Device Alerts: SNMP Traps and SMTP Configuration

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды

Deliberant FWBD0501, Руководство пользователя

Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды