Deliberant FWBD0501 Скачать руководство пользователя страница 46

Страница: 46 / 67

User’s

Guide

deliberant

Page

Figure 44 – Traffic Shaping Configuration

Limit

all

traffic

Enable download shaping

– select to enable limitation of the download traffic.

Download limit, kbps

– specify the maximum download (from wireless interface to Ethernet interface)

bandwidth value in Kbps.

Download burst, kbytes

– specify the download burst size in kbytes.

Enable upload shaping

– select to enable limitation of the upload traffic.

Upload limit, kbps

– specify the maximum upload (from Ethernet interface to wireless interface)

bandwidth value in Kbps.

Upload burst, kbytes

– specify the upload burst size in kbytes

Limit

per

traffic

Use + button to create new traffic limitation rules

Figure 45 – Traffic Shaping: Per IP Limitation

IP address

– specify IP address for which the traffic will be limited.

Down rate, kbps

– specify the maximum download (from wireless interface to Ethernet interface)

bandwidth value in Kbps.

Down burst, kbytes

– specify the download burst size in kbytes.

UP rate, kbps

– specify the maximum upload (from Ethernet interface to wireless interface)

bandwidth value in Kbps.

UP burst, kbytes

– specify the download burst size in kbytes

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Deliberant FWBD0501, Руководство пользователя, Страница: 46 / 67

Результаты поиска

Содержание FWBD0501

Отзывы: