Deliberant FWBD0501 Скачать руководство пользователя страница 18

Страница: 18 / 67

User’s

Guide

deliberant

Page

Site Survey

– information about other wireless networks in the local area.

Delayed reboot

– setup delayed reboot for APC unit.

Ping

– perform ping command.

Traceroute

– perform graphical traceroute command.

Spectrum analyzer

– check the signal strength on available channels.

Appling

and

Saving

Configuration

Changes

There are three general buttons located on the right top corner of the WEB GUI allowing managing
device configuration:

Apply

– if pressed new configuration settings are applied instantly. It will take few seconds and

the device will be running with new settings. It should be noted that pressing Apply button
settings are not written to the permanent memory. Therefore, if the device is rebooted it will
start with old configuration settings.

Discard

– if pressed parameter changes are discarded. It should be noted that if Apply or

Save&Apply is pressed it is not possible to discard changes.

Save&Apply

– if pressed new configuration settings are applied instantly and written to the

permanent memory.

It is not required to press

Apply

Save&Apply

in every Web GUI tab. The device

remembers all changes made in every tab and after action button is used, all changes will
be applied.

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды

Deliberant FWBD0501, Руководство пользователя

Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды