Deliberant FWBD0501 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 67

background image

User’s

Guide

deliberant

Page

35

Wireless

Mode:

Station

Station WDS

has the same wireless settings.

The Station wireless settings a bit differ from the Access Point’s settings: there is possibility to scan
SSID of the surrounding APs and choose the required one.

Use Wireless Settings to setup radio interface of the device.

Figure 27 – Station Wireless Settings

Basic

Wireless

Settings

SSID

– specify the SSID of the wireless network device.

Scan

– click this button to scan for surrounding wireless networks. Found network SSID’s will be

available in drop down menu.

IEEE mode

– specify the wireless network mode.

Channel width

– The default channel bandwidth for 802.11 radio is 20MHz. The 802.11n allow

channel bonding in such way the total channel width becomes 40MHz.

«
...
33
34
35
36
37
...
»

Содержание FWBD0501




































































Отзывы:

Нет отзывов

Похожие инструкции для FWBD0501

Бренд: Qongle Страницы: 13

Бренд: Qixiang Technology Страницы: 11

EliteConnect SMC2555W-AG2

Бренд: SMC Networks Страницы: 2

Бренд: Meru Networks Страницы: 73

Бренд: Digisol Страницы: 142

Бренд: Cisco MERAKI Страницы: 19

Aruba 318 Series

Бренд: Hewlett Packard Enterprise Страницы: 2

Бренд: Draytek Страницы: 1

Бренд: Kraun Страницы: 55

Бренд: Brickcom Страницы: 52

Бренд: Alfa Network Страницы: 115

Бренд: Xterasys Страницы: 74

Бренд: EnGenius Страницы: 2

Бренд: ConnectGear Страницы: 11

Бренд: ConnectGear Страницы: 36

Cellferno M1200

Бренд: PowerTec Страницы: 12

Бренд: Nexcom Страницы: 89

airMAX BulletAC-IP67-US

Бренд: Ubiquiti Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды