Deliberant FWBD0501 Скачать руководство пользователя страница 17

Страница: 17 / 67

User’s

Guide

deliberant

Page

General

Device

Operation

Web

Management

Structure

The main web management menu is displayed after successfully login into the system (see the figure
below). From this menu all essential configuration pages are accessed. The active menu tab is
displayed in a different color:

By default the

Status | Information

menu is activated where the main device information is displayed.

The APC web management menu has the following structure:

Status

Information

– displays general information and of the device.

Network

– displays network statistics of the device.

Wireless

– displays information about connected stations on each wireless interface (only on AP

wireless mode).

Routes

– displays unit’s route table.

ARP

– displays ARP table.

Configuration

Network

– to configure network mode, Ethernet speed, IP settings, management and data

VLANs, DHCP, PPPoE.

Wireless

– specify wireless mode (AP, Station, Station WDS, iPoll AP, iPoll Station), country,

SSID, IEEE mode, channel configuration, security and advanced radio settings.

Virtual AP

– create and setup virtual AP (only in AP wireless mode).

Wireless ACL

– access control by MAC address (only in AP and IPoll AP wireless modes).

Traffic shaping –

download and upload traffic control.

Port forwarding

– port forwarding rules (only in router network mode for AP and IPoll AP).

Static routes

– static route rules (only in router network mode for AP and IPoll AP).

Services

WNMS

– set WNMS server/collector URL allowing remote device configuration and monitoring.

System Alerts

– set alerts which can be sent via SNMP Traps or/and SMTP notifications.

SNMP

– SNMP service settings allowing remote device monitoring.

Clock/NTP

– set device date manually or enable and configure NTP service.

SSH

– control SSH connection.

HTTP

– control HTTP connection.

Autodiscovery

– control device autodiscovery function (only on Station, Station WDS and IPoll

Station wireless modes).

System

Administration

– change password, reboot, restore factory default settings, backup/restore

configuration, troubleshooting file support.

Log

– view device log, set system log forwarding settings.

LED

– control operation of LEDs.

Firmware upgrade

– upgrade device firmware.

Tools

Antenna alignment

– measure received signal quality of the wireless link to align antenna in the

best direction.

Содержание FWBD0501



































































Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды

Deliberant FWBD0501, Руководство пользователя

Результаты поиска

Содержание FWBD0501

Отзывы:

Похожие инструкции для FWBD0501

Бренды по названию

Популярные бренды