Datex-Ohmeda 7100 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 158

background image

7100 Anesthesia Ventilator

5-4

02/03 1006-0836-000

5.3 Alarm and Error messages

The Service Mode (refer to section 4) includes a log of the 20 most recent
Alarm messages (not shaded) and Error messages (shaded) experienced by
the ventilator system.

If a User Alarm persists after the recommended action has been performed,
the message indicates the probable component and related circuit that needs
repair. Use the Service Mode tests to isolate the fault. The items in the Service
Repair column indicate the path from the named component to the control
board.

Alarm Message

Error Message

Message

Alarm/Error

Cause

User Action/Concerns

Service Repair

12 Hour Test

w

User Alarm

System in use for more than

12 hours without a
powerup self test.

At end of case, move the system

switch from On to Standby to
On.

+12V Analog

Out-of- Range

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

-12V Analog

Out-of- Range

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

12V -10VA Test

Out-of-Range

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

Absorber Panel Open User Alarm

The top panel on Aestiva is

not completely closed.

ABS on Aespire in not

completely engaged.

Close the panel.

Reinstall ABS.

If persists, check:
• Panel switch
• Harness to MIA/

VMB

• MIA/VMB
• Cable to CB/J12

A/D Converter

Failure

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

Apnea Alarm

Standby

User Alarm

Normal condition after End

Case, powerup, or ACGO
change from On to Off.

Monitoring resumes after first

breath (mechanical) or 2
breaths within 30 sec (non-
mechanical).

Apnea Alarm Off

User Alarm

The cardiac bypass option is

selected (Alarm Settings
menu).

Apnea alarms are turned off

when this option is selected.

«
...
82
83
84
85
86
...
»

Содержание 7100































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7100

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Ultraflex Страницы: 3

Бренд: H&S Страницы: 42

Бренд: MacDon Страницы: 2

Бренд: Rainin Instrument Страницы: 16

Бренд: Omlet Страницы: 60

Бренд: Qiagen Страницы: 48

Бренд: Qiagen Страницы: 162

Бренд: Qazqa Страницы: 4

Бренд: Qlightec Страницы: 12

Бренд: Baileigh Industrial Страницы: 12

Бренд: Wacker Neuson Страницы: 34

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: Abus Страницы: 8

Бренд: VaBroom Страницы: 4

Бренд: Veit Brisay Страницы: 18

Бренд: ABB Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды