Datex-Ohmeda 7100 Скачать руководство пользователя страница 82

Страница: 82 / 158

7100 Anesthesia Ventilator

5-2

02/03 1006-0836-000

5.1 Troubleshooting instructions

Some ventilator problems may not generate any ventilator messages, even
though the ventilator may not be functioning correctly:

•

Refer to section 5.2 Troubleshooting guide.

For ventilator problems that result in an Alarm or Error message:

•

Refer to section 5.3 Alarm and Error messages.

To help isolate a problem:

•

Refer to section 5.4 Troubleshooting Flowcharts.

5.2 Troubleshooting guide

Symptom

Probable cause

Action

• Continuous alarm

sounds whenever
system switch is turned
On —

5V Fail Alarm

1. Failure in power section of Control Board.

1. Replace Control Board.

The Control Board includes a hardware generated alarm that sounds continuously if the 5 volt supply

fails.

Symptom

Probable cause

Action

•

AC LED not lit

(Power cord plugged into

live receptacle; AC Inlet
circuit breaker On)

(The problem is most likely

in the +6V supply or in
the LED circuit.)

1. Blown fuses in Control Module’s AC receptacle

2. Universal power supply

3. Front panel keyboard (LED is part of it)

4. Control board

1. Check/replace fuses.

2. Check power supply output.

3. Check ribbon cable connection; replace front

panel keyboard.

4. +6V-------R11------ to LED; replace Control Board.

The LED is powered by the +6V supply from the universal power supply. Turn system switch to On. If ventilator operates from the

backup battery, check 1 and 2. If ventilator operates from line power, check 3 and 4.

Symptom

Probable cause

Action

•

Nothing happens when

System switch is
turned On

(The problem is most likely

somewhere between
the system switch and
the control board.)

1. Cable from J11 of Control Board to SAB/SICB.

2. Cable from System Switch to SAB/SICB.

3. Serial Adapter Board (SAB -Aestiva)

Serial Isolation Connector Board
(SICB - Aespire)

1. Check/jumper cable connection; replace cable.

2. Check cable connection; replace cable.

3. Replace SAB/SICB.

Turning the system switch to On should pull the

Reeeem

m___

Onnnn signal low on the control board. The above actions verifies the integrity of

the

Reeeem

m___

Onnnn signal path. First, jumper pins 8 and 15 of J11 on control board to verify that the control board itself is OK.

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды