Datex-Ohmeda 7100 Скачать руководство пользователя страница 126

Страница: 126 / 158

7100 Anesthesia Ventilator

7-20

02/03 1006-0836-000

7.5 Serial Adapter Board (SAB) and Power Cord/Harness

Note:

This section applies only to an

Aestiva machine

. For an

Aespire

machine

, refer to the Aespire Technical Reference Manual for details about the

Serial Isolation and Connector Board.

The SAB is located in the electrical enclosure area behind the AC Inlet module.
The two cables that connect to the MIA are behind the rear panel in the
pneumatics area.

WARNING

Disconnect the power cord from the wall before attempting to remove or
repair any circuit board to avoid shock hazard.

WARNING

The AC inlet module is very heavy. Use caution when removing it from the
anesthesia enclosure.

Caution

The circuit boards are electrostatic sensitive. Use an anti-static
workstation and wear a wrist grounding strap when handling a circuit
board.

To gain access to

the Serial Adapter Board

1. Remove the AC inlet module from the rear of the Aestiva Anesthesia

Machine.

a. Loosen the two captive M4 screws.

b. Pulling on the two captive screws, cautiously slide the AC inlet mod-

ule out only halfway from the enclosure. Use the two side handles
(cutouts in the sheet metal) to lift out the AC inlet module from the en-
closure.

WARNING

The AC inlet module is very heavy. Use caution

when removing it from the anesthesia enclosure.

2. Remove the electronics compartment cover by removing the four Phillips

head screws (two along top edge, one along each side).

3. Remove the rear panel

(see Section 4.1.1 of the Aestiva Anesthesia Machine Service Manual).

Captive screws

Cutout handles

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Похожие инструкции для 7100

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Похожие инструкции для 7100

Бренды по названию

Популярные бренды