Datex-Ohmeda 7100 Скачать руководство пользователя страница 89

Страница: 89 / 158

5 Troubleshooting

1006-0836-000 02/03

5-9

Low Paw

User Alarm

Paw does not rise at least

4 cm above Pmin during
the last 20 sec.

Are circuit connections OK?
Look at the Paw gauge on the

absorber.

Look for circuit disconnection.

Low

◊

User Alarm

Exhaled minute volume

less than low limit alarm
setting. This alarm is
suspended for 9 breaths
after you change the
ventilator settings.

Check patient condition.
Check tubing connections.
Check alarm settings.

Low V

User Alarm

Exhaled tidal volume

less than low limit alarm
setting. This alarm is
suspended for 9 breaths
after you change the
ventilator settings.

Check patient condition.
Check tubing connections.
Check alarm settings.

Memory (EEPROM)

Fail

User Alarm

The system cannot access

some stored values.

Default settings are used.

Ventilation is still possible but
service is necessary.

Replace:
• Control Board.

Memory (Flash)

Failure

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

Memory (RAM)

Failure

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

Memory (Redundant

Storage) Failure

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is still available.

Replace:
• Control Board.

Memory (Video)

Failure

Error

Minimum
Shutdown

Ventilator malfunction.

Ventilate manually.

Monitoring is not reliable.

Replace:
• Control Board.

Monitoring Only

User Alarm

A severe malfunction

prevents mechanical
ventilation.

Other alarms may also

occur.

Ventilate manually. Cycle system

power (On- Standby-On).

If the alarm clears, restart

mechanical ventilation.

Replace:
• Control Board.

No Circuit Module

User Alarm

The patient circuit module is

not installed
(Aestiva only).

Install a module.
Optical sensors look for tabs on

the back of the module.

Is the module assembled?
Are sensors dirty?

If persists, check:
• Circuit

Identification
Board

• Harness to MIA/

VMB

• MIA/VMB
• Cable to CB/J12

Message

Alarm/Error

Cause

User Action/Concerns

Service Repair

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды