Datex-Ohmeda 7100 Скачать руководство пользователя страница 91

Страница: 91 / 158

5 Troubleshooting

1006-0836-000 02/03

5-11

Paw < -10 cm H

User Alarm

Subatmospheric pressure

(<-10 cm H

O).

Check patient condition,

spontaneous activity?
Increase fresh gas flow. Look
for high flow through gas
scavenging.

Calibrate the flow sensors. With

active scavenging, check the
negative relief valve on the
receiver.

PEEP Valve (DAC)

Failure

Error

Minimum
Monitoring

Indicates a failure of the

control circuit for the
PEEP Valve.

Ventilate manually.

Replace:
• Control Board.

PEEP Valve (Voltage)

Failure

Error

Minimum
Monitoring

Indicates a problem with the

PEEP Valve or the
connections to the PEEP
Valve.

Ventilate manually.

Check/Replace:
• PEEP Valve
• PEEP Valve

harness

• PEB/VEB
• Cable to CB/J14
• Control Board.

PEEP Safety Valve

(Drive) Failure

Error

Minimum
Monitoring

Indicates a higher than

allowed current draw on
the PEEP Safety Valve.

Ventilate manually.

Check/Replace:
• PEEP Safety Valve
• PEEP Safety Valve

harness

• PEB/VEB
• Cable to CB/J14
• Control Board.

PEEP Safety Valve

Failure

Error

Minimum
Monitoring

Indicates that the powerup

test of the PEEP Safety
Valve failed.

Ventilate manually.

Check/Replace:
• PEEP Safety Valve
• PEEP Safety Valve

harness

• PEB/VEB
• Cable to CB/J14
• Control Board.

Pinsp Not Achieved

User Alarm

Indicates a problem with

breathing circuit
connections or that the
ventilator is unable to
deliver requested
pressure to the patient.

Check breathing circuit

connections. Check settings.

Pressure Monitoring

Channel Failure

Error

Minimum
Monitoring

Indicates a problem with

patient airway
overpressure monitor.

Ventilate manually.

Check/Replace:
• PEB/VEB
• Cable to CB/J14
• Control Board.

Message

Alarm/Error

Cause

User Action/Concerns

Service Repair

Содержание 7100






























































































































































Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda 7100, Техническое справочное руководство

Результаты поиска

Содержание 7100

Отзывы:

Бренды по названию

Популярные бренды