Datalogic SG EASY One Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 153

background image

5-45

Y15 turns ON in Initial, Protection or Configuration state.
Y16 turns ON when in Run state.
Refer to “Chapter 4 BASIC OPERATION”, or “Chapter 6 TROUBLESHOOTING”, for details of the each
state.

Warning

The monitor outputs are not safety outputs. Do not use these to construct a safety system.

●

Solenoid outputs: Y17 and Y20

Y17 and Y20 are outputs for solenoid control that are used for a safety switch with a lock.
In the Run state, when the safety outputs are OFF and 1 or more safety inputs are OFF, the
solenoid outputs are turned ON. When all safety inputs are ON, the solenoid outputs are turned
OFF, although the start input is not activated.

Warning

Solenoid outputs are not safety outputs. Do not use these to construct a safety system.

Caution

Refer to "Chapter 2 PRODUCT SPECIFICATIONS" for specifications of each input and output.

«
...
85
86
87
88
89
...
»

Содержание SG EASY One


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для SG EASY One

Бренд: Baccara Страницы: 16

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: Paradox Страницы: 6

Бренд: 2gig Technologies Страницы: 6

Бренд: Linak Страницы: 33

LMT070DICFWD-NJN

Бренд: Topway Страницы: 34

Бренд: Apex Toys Страницы: 7

Dual Motor Focus Controller

Бренд: Pegasus Astro Страницы: 16

Бренд: QUANT Страницы: 24

ServLink ACR3500A

Бренд: Black Box Страницы: 115

GLOFA G7M-DR20U

Бренд: LS Industrial Systems Страницы: 367

Бренд: Computherm Страницы: 40

Бренд: M-E Страницы: 36

Бренд: Task Force Tips Страницы: 8

Бренд: Steren Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды