Datalogic SG EASY One Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 153

background image

Warning



Do not connect devices having input and output specifications that do not satisfy the
requirements of the SG-ONE.
Refer to the following for information on the requirements of connected devices.

Connected Control Device

Requirements

Emergency stop switch

Device equipped with a direct opening action mechanism conforming to

IEC/EN60947-5-5 or indicated in IEC/EN60947-5-1

Interlock switch,
limit switch

Device equipped with a direct opening action mechanism indicated in

IEC/EN60947-5-1

Safety switch with lock

Spring lock safety switch with solenoid

Mode select switch

Device conforming to regulations of the country where used and required

categories (for example, switch conforming to IEC/EN60947-1)

Enabling switch

Device conforming to IEC/EN60947-5-8 (or IEC/EN60947-5-1)

Solid state output device

Device conforming to regulations of the country where used (for example,

safety light curtain conforming to IEC/EN61496-1)
PNP output (See Note 1)

Non-contact interlock switch Device designed to work together with hinged, sliding, or lift-off guards and

barriers conforming to regulations of the country where used

Safety relay

Relay equipped with forced guide mechanism or conforming to EN50205

Contactor
(electromagnetic switch)

Contactor equipped with forced guide mechanism

Other control devices

Use start switches and other devices that conform to the regulations of the

country where used.

Muting sensor

Device conforming to IEC/EN60947-5-2 as shown below
-3 wire transmission (dark on) photoelectric switch which has a PNP open

collector output.
-3 wire (normal open) proximity switch which has a PNP open collector

output.

Muting lamp

Incandescent bulb indicator light conforming to IEC/EN60947-1 or

IEC/EN60947-5-1
Note 2: It is not possible to detect a disconnection of the muting lamp when

using an LED indicator light.



Make sure that the end-user thoroughly understands the contents of this user’s manual.

Note 1: Use the solid state output device that sends output signal of the waveforms shown below.

Otherwise the SG-ONE cannot process the input signal correctly.

Software version

1.20

1.30 or later

Applicable solid state
output device

Pulse output off cycle of 40ms or
more and an off time of 1ms or less.

Pulse output off time of 0.5ms or
less or same as version 1.20.

(Waveform of solid sate
output)

The device may not be usable even if the above specifications are satisfied. Be sure to
thoroughly confirm operations using the actual device.

Software version is described at the next of serial number on the product label.
  S/N****-***** 1V130 ****
                                                              Software version 1.30
                                                              Serial number

Off cycle: 40ms or more

Off time:
1ms or less

Off time: 0.5ms or less

«
...
3
4
5
6
7
...
»

Содержание SG EASY One


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для SG EASY One

Бренд: BADODOSECURITY Страницы: 8

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: Samson Страницы: 78

Бренд: LAS Страницы: 6

Бренд: Bettis Страницы: 18

Бренд: EisSound Страницы: 10

Бренд: Cardin Elettronica Страницы: 56

Бренд: Swagelok Страницы: 16

Бренд: ICP DAS USA Страницы: 7

Бренд: C-TEC Страницы: 28

Бренд: ADLINK Technology Страницы: 37

Samos Pro Compact SP-COP2

Бренд: Wieland Страницы: 36

Infi 90 IMCPM03

Бренд: Bailey Страницы: 61

SEPCOM SIP BED Easy

Бренд: WAMGROUP Страницы: 52

Бренд: DH Instruments Страницы: 30

Бренд: Quick Страницы: 16

SPACOMMAND CP3800 Series

Бренд: Pentair Страницы: 36

Бренд: tecatlantis Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды