Datalogic SG EASY One Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 153

background image

5-25

●

State monitor outputs: Y14 to Y16

Y14 to Y16 are monitoring outputs for the internal status of the SG-ONE.
Y14 turns ON when in Initial or Stop state.
Y15 turns ON in Initial, Protection or Configuration state.
Y16 turns ON in Run state.
Refer to “Chapter 4 BASIC OPERATION”, or “Chapter 6 TROUBLESHOOTING”, for details of the
each state.

Warning

Monitor outputs are not safety outputs. Do not use these to construct a safety system.

●

Solenoid outputs: Y17 and Y20

Y17 and Y20 are outputs for solenoid control that are used for safety interlock switch with a
solenoid lock.
In the Run state, when the safety outputs are OFF and 1 or more safety inputs are OFF, the
solenoid outputs are turned ON. When all safety inputs are ON, the solenoid outputs are turned
OFF, although start input is not activated.

Warning

Solenoid outputs are not safety outputs. Do not use these to construct a safety system.

Caution

Refer to "Chapter 2 PRODUCT SPECIFICATIONS" for specifications of each input and output.

«
...
65
66
67
68
69
...
»

Содержание SG EASY One


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для SG EASY One

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: Canarm Страницы: 3

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Frigolink FVB110B

Бренд: WURM Страницы: 4

Бренд: Matelec Страницы: 16

Бренд: Measurement Computing Страницы: 32

Бренд: Climatisation Страницы: 52

Бренд: TECOM Страницы: 8

Бренд: MX Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды