Datalogic SG EASY One Скачать руководство пользователя страница 28

Страница: 28 / 153

3-2

●

Prevent SG-ONE from falling while moving or transporting the SG-ONE, otherwise damage or

malfunction of the SG-ONE may result.

●

Prevent metal fragments and pieces of wire from dropping inside the SG-ONE housing.

●

Install SG-ONE, so that there is adequate spacing from walls, heat generating bodies, and

peripherals, taking into consideration space requirements for maintenance and ventilation.

●

Install SG-ONE on 35mm DIN rails with BNL6 mounting clips (sold separately) on both sides of

SG-ONE.

●

Perform wiring to the connectors with proper cables or ferrules.

●

Ground FE terminal to assure electromagnetic compatibility (EMC)

●

Use common 0V DC, if different power supplies are used for SG-ONE and other devices (ex.

safety light curtains).

●

Install wiring for the inputs and outputs so that it is separated from power lines.

Содержание SG EASY One


























































































































































Результаты поиска

Содержание SG EASY One

Отзывы:

Похожие инструкции для SG EASY One

Бренды по названию

Популярные бренды

Datalogic SG EASY One, Инструкция по эксплуатации

Результаты поиска

Содержание SG EASY One

Отзывы:

Похожие инструкции для SG EASY One

Бренды по названию

Популярные бренды