D-Link DGS-3024 Скачать руководство пользователя

Страница: 94 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

enable gvrp

Purpose

Used to enable GVRP on the Switch.

Syntax

enable gvrp

Description

This command, along with

disable gvrp

below, is used to enable

and disable GVRP on the Switch, without changing the GVRP
configuration on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable the generic VLAN Registration Protocol (GVRP):

DGS-3024:4#enable gvrp

Command: enable gvrp

Success.

DGS-3024:4#

disable gvrp

Purpose

Used to disable GVRP on the Switch.

Syntax

disable gvrp

Description

This command, along with

enable gvrp

above, is used to enable

and disable GVRP on the Switch, without changing the GVRP
configuration on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable the Generic VLAN Registration Protocol (GVRP):

DGS-3024:4#disable gvrp

Command: disable gvrp

Success.

DGS-3024:4#

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды