D-Link DGS-3024 Скачать руководство пользователя

Страница: 48 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

config snmp system_location

Purpose

Used to enter a description of the location of the Switch.

Syntax

config snmp system_location {<sw_location>}

Description

The

config snmp system_location

command is used to enter a

description of the location of the Switch. A maximum of 255
characters can be used.

Parameters

<sw_location>

- A maximum of 255 characters is allowed. A NULL

string is accepted if there is no location desired.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure the Switch location for “

HQ 5F

”:

DGS-3024:4#config snmp system_location HQ 5F

Command: config snmp system_location HQ 5F

Success.

DGS-3024:4#

config snmp system_name

Purpose

Used to configure the name for the Switch.

Syntax

config snmp system_name {<sw_name>}

Description

The

config snmp system_name

command configures the name

of the Switch.

Parameters

<sw_name>

- A maximum of 255 characters is allowed. A NULL

string is accepted if no name is desired.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure the Switch name for “

DGS-3024 Switch”

DGS-3024:4#config snmp system_name DGS-3024 Switch

Command: config snmp system_name DGS-3024 Switch

Success.

DGS-3024:4#

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды