D-Link DGS-3024 страница 77 Скачать руководство пользователя

Страница: 77 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

delete fdb

address resides.

<macaddr>

−

The MAC address that will be added to the forwarding

table.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To delete a permanent FDB entry:

DGS-3024:4#delete fdb default 00-00-00-00-01-02

Command: delete fdb default 00-00-00-00-01-02

Success.

DGS-3024:4#

clear fdb

Purpose

Used to clear the Switch’s forwarding database of all dynamically
learned MAC addresses.

Syntax

clear fdb [vlan <vlan_name 32> | port <port> | all]

Description

This command is used to clear dynamically learned entries to the
Switch’s forwarding database.

Parameters

<vlan_name 32>

−

The name of the VLAN on which the MAC

address resides.

port <port>

−

The port number corresponding to the MAC destination

address. The Switch will always forward traffic to the specified
device through this port.

all

−

Clears all dynamic entries to the Switch’s forwarding database.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To clear all FDB dynamic entries

DGS-3024:4#clear fdb all

Command: clear fdb all

Success.

DGS-3024:4#

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды