D-Link DGS-3024 страница 74 Скачать руководство пользователя

Страница: 74 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

ORWARDING

ATABASE

OMMANDS

The layer 2 forwarding database commands in the Command Line Interface (CLI) are listed (along with the appropriate
parameters) in the following table.

Command Parameters

create fdb

<vlan_name 32> <macaddr> port <port>

create multicast_fdb

<vlan_name 32> <macaddr>

config multicast_fdb

<vlan_name 32><macaddr> [add | delete] <portlist>

config fdb aging_time
minutes

show fdb aging_time

clear fdb

[vlan <vlan_name 32> | port <port> | all]

show multicast_fdb

{vlan <vlan_name 32> | mac_address <macaddr>}

show fdb

{port <port> | vlan <vlan_name 32> mac_address <macaddr> |
static | aging_time}

delete fdb

<vlan_name 32> <macaddr>

Each command is listed, in detail, in the following sections.

create fdb

Purpose

Used to create a static entry to the unicast MAC address forwarding
table (database)

Syntax

create fdb <vlan_name 32> <macaddr> port <port>

Description

This command will make an entry into the Switch’s unicast MAC
address forwarding database.

Parameters

<vlan_name 32>

−

The name of the VLAN on which the MAC

address resides.

<macaddr>

−

The MAC address that will be added to the forwarding

table.

port <port>

−

The port number corresponding to the MAC destination

address. The Switch will always forward traffic to the specified
device through this port.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To create a unicast MAC FDB entry

DGS-3024:4#create fdb default 00-00-00-00-01-02 port 2

Command: create fdb default 00-00-00-00-01-02 port 2

Success.

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды