D-Link DGS-3024 Скачать руководство пользователя

Страница: 49 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

MAC N

OTIFICATION

OMMANDS

The MAC notification commands in the Command Line Interface (CLI) are listed, in the following table, along with their
appropriate parameters.

Command Parameters

enable mac_notification

disable mac_notification

config mac_notification

{interval <int 1-2147483647> | historysize <int 1-500>}

config mac_notification ports

[<portlist> | all] [enable | disable]

show mac_notification

show mac_notification ports

Each command is listed, in detail, in the following sections.

enable mac_notification

Purpose

Used to enable global MAC address table notification on the
Switch.

Syntax

enable mac_notification

Description

This command is used to enable MAC Address Notification without
changing configuration.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example Usage:

To enable MAC notification without changing basic configuration:

DGS-3024:4#enable mac_notification

Command: enable mac_notification

Success.

DGS-3024:4#

disable mac_notification

Purpose

Used to disable global MAC address table notification on the Switch.

Syntax

disable mac_notification

Description

This command is used to disable MAC Address Notification without
changing configuration.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды