D-Link DGS-3024 Скачать руководство пользователя | Manualshive

Страница: 88 / 139

background image

DGS-3024 Layer 2 Switch CLI Reference Manual

14

P

ORT

M

IRRORING

C

OMMANDS

The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.

Command Parameters

config mirror

{source port <port> | ingress_target [disable | port <port>] |
egress_target [disable | port <port>]}

enable mirror

disable mirror

show mirror

Each command is listed, in detail, in the following sections.

config mirror

Purpose

Used to configure a mirror port

−

source port pair on the Switch.

Syntax

config mirror {source port <port> | ingress_target [disable | port
<port>] | egress_target [disable | port <port>]}

Description

This command allows a range of ports to have all of their traffic also sent to
a designated port, where a network sniffer or other device can monitor the
network traffic. In addition, you can specify that only traffic received by or
sent by one or both is mirrored to the Target port.

Parameters

source port <port>

−

This specifies the port or ports being mirrored.

ingress_target

– This parameter denotes that the user wishes to mirror

traffic entering the port specified in the source port parameter.

disable

– Entering this parameter will disable ingress mirroring for

the source port.

port <port>

- Specifies the target port to where ingress traffic will be

mirrored. This port cannot be the same as the source port and also
cannot have a slower transfer speed as the source port.

egress_port

- This parameter denotes that the user wishes to mirror traffic

leaving the port specified in the source port parameter.

disable

– Entering this parameter will disable egress mirroring for

the source port.

port <port>

- Specifies the target port to where egress traffic will be

mirrored. This port cannot be the same as the source port and also
cannot have a slower transfer speed as the source port.

Restrictions

Any target port cannot be listed as a source port. Only administrator-level
users can issue this command.

Example usage:

To add the mirroring ports:

86

«
...
86
87
88
89
90
...
»

Содержание DGS-3024












































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3024

Бренд: Magnetrol Страницы: 12

Бренд: Magnetrol Страницы: 24

Бренд: Daxten Страницы: 7

COOPER POWER SERIES

Бренд: Eaton Страницы: 32

Бренд: Keithley Страницы: 452

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 62

Бренд: Black Box Страницы: 4

Universal Videohub 288

Бренд: Blackmagicdesign Страницы: 107

Бренд: BluStream Страницы: 4

Бренд: Unipoe Страницы: 9

Бренд: Cabletron Systems Страницы: 116

Бренд: Lanpro Страницы: 16

Бренд: J-Tech Digital Страницы: 81

Бренд: Cable Electronics Страницы: 12

Signal Distribution Box SDB45

Бренд: Audiovox Страницы: 12

Бренд: Clare Controls Страницы: 2

Бренд: Vertiv Страницы: 24

Бренд: Sensor Switch Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды