D-Link DGS-3024 Скачать руководство пользователя

Страница: 106 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

enable igmp_snooping

Purpose

Used to enable IGMP snooping on the Switch.

Syntax

enable igmp_snooping {forward_mcrouter_only}

Description

This command allows you to enable IGMP snooping on the Switch. If

forward_mcrouter_only

is specified, the Switch will only forward all

multicast traffic to the multicast router, only. Otherwise, the Switch forwards
all multicast traffic to any IP router.

Parameters

forward_mcrouter_only

−

Specifies that the Switch should only forward all

multicast traffic to a multicast-enabled router. Otherwise, the Switch will
forward all multicast traffic to any IP router.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable IGMP snooping on the Switch:

DGS-3024:4#enable igmp_snooping

Command: enable igmp_snooping

Success.

DGS-3024:4#

disable igmp_snooping

Purpose

Used to disable IGMP snooping on the Switch.

Syntax

disable igmp_snooping

Description

This command disables IGMP snooping on the Switch. IGMP snooping can
be disabled only if IP multicast routing is not being used. Disabling IGMP
snooping allows all IGMP and IP multicast traffic to flood within a given IP
interface.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable IGMP snooping on the Switch:

DGS-3024:4#disable igmp_snooping

Command: disable igmp_snooping

Success.

DGS-3024:4#

104

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды