D-Link DGS-3024 Скачать руководство пользователя

Страница: 66 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

config syslog host

Restrictions Only

administrator-level users can issue this command.

Example usage:

To configure a syslog host:

DGS-3024:4#config syslog host all severity all facility local0

Command: config syslog host all severity all facility local0

Success.

DGS-3024:4#

delete syslog host

Purpose

Used to remove a syslog host, that has been previously configured,
from the Switch.

Syntax

delete syslog host [<index 1-4> | all]

Description

The

delete syslog host

command is used to remove a syslog host

that has been previously configured from the Switch.

Parameters

<index 1-4>

−

Specifies that the command will be applied to an index

of hosts. There are four available indexes, numbered 1 through 4.

all

−

Specifies that the command will be applied to all hosts.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To delete a previously configured syslog host:

DGS-3024:4#delete syslog host 4

Command: delete syslog host 4

Success.

DGS-3024:4#

show syslog host

Purpose

Used to display the syslog hosts currently configured on the Switch.

Syntax

show syslog host {<index 1-4>}

Description

The

show syslog host

command is used to display the syslog

hosts that are currently configured on the Switch.

Parameters

<index 1-4>

−

Specifies that the command will be applied to an index

of hosts. There are four available indexes, numbered 1 through 4.

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды