D-Link DGS-3024 Скачать руководство пользователя

Страница: 13 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

ASIC

WITCH

OMMANDS

The basic switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.

Command Parameters

create account

[admin | user] <username 15>

config account

show account

show session

show switch

show serial_port

config serial_port

{baud_rate [9600 | 19200 | 38400 | 115200] auto_logout [never |
2_minutes | 5_minutes| 10_minutes | 15_minutes]}

enable clipaging

disable clipaging

enable telnet

<tcp_port_number 1-65535>

disable telnet

enable web

<tcp_port_number 1-65535>

disable web

save

reboot

reset

{[config | system]}

logout

ping

<ipaddr> {times <value 1-255>} {timeout <sec 1-99>}

Each command is listed, in detail, in the following sections.

create account

Purpose

Used to create user accounts.

Syntax

create [admin | user] <username 15>

Description

The create account command is used to create user accounts that
consist of a username of 1 to 15 characters and a password of 0 to
15 characters. Up to 8 user accounts can be created.

Parameters

admin <username>

user <username>

Restrictions Only

Administrator-level users can issue this command.

Usernames can be between 1 and 15 characters.

Содержание DGS-3024












































































































































Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды

D-Link DGS-3024, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3024

Отзывы:

Похожие инструкции для DGS-3024

Бренды по названию

Популярные бренды