D-Link DGS-3024 страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 139

background image

DGS-3024 Layer 2 Switch CLI Reference Manual

config syslog host

Purpose

Used to configure the syslog protocol to send system log data to a
remote host.

Syntax

config syslog host {host [all <index 1-4>]} {severity
[informational | warning | all] | facility [local0 | local1 | local2 |
local3 | local4 | local5 | local6 | local7] | udp_port
<udp_port_number> | ipaddress <ipaddr> | state [enable |
disable]}

Description

The

config syslog host

command is used to configure the syslog

protocol to send system log information to a remote host.

Parameters

all

−

Specifies that the command will be applied to all hosts.

<index 1-4>

−

Specifies that the command will be applied to an index

of hosts. There are four available indexes, numbered 1 through 4.

severity

−

Severity level indicator. These are described in the

following:

Bold

font indicates that the corresponding severity level is currently

supported on the Switch.

Numerical Severity

Code

0 Emergency: system is unusable

1 Alert: action must be taken immediately

2 Critical: critical conditions

3 Error: error conditions

4 Warning: warning conditions

5 Notice: normal but significant condition

6 Informational: informational messages

7 Debug: debug-level messages

informational

−

Specifies that informational messages will be sent to

the remote host. This corresponds to number 6 from the list above.

warning

−

Specifies that warning messages will be sent to the

remote host. This corresponds to number 4 from the list above.

all

−

Specifies that all of the currently supported syslog messages

that are generated by the Switch will be sent to the remote host.

facility

−

Some of the operating system daemons and processes

have been assigned Facility values. Processes and daemons that
have not been explicitly assigned a Facility may use any of the "local
use" facilities or they may use the "user-level" Facility. Those
Facilities that have been designated are shown in the following:

Bold

font indicates the facility values the Switch currently supports.

Numerical Facility

Code

0 kernel messages

1 user-level messages

2 mail system

3 system daemons

62

«
...
62
63
64
65
66
...
»

Содержание DGS-3024












































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3024

Switch 4500 Family

Бренд: 3Com Страницы: 16

PathBuilder S200 Series

Бренд: 3Com Страницы: 32

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 139

CoreBuilder 7000

Бренд: 3Com Страницы: 150

CoreBuilder 7000

Бренд: 3Com Страницы: 264

Бренд: 3Com Страницы: 574

Бренд: 3Com Страницы: 333

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 70

OfficeConnect 3C16790C

Бренд: 3Com Страницы: 18

Бренд: 3Com Страницы: 1314

SuperStack II Switch 1100

Бренд: 3Com Страницы: 62

Бренд: BABBITT Страницы: 14

Бренд: BABBITT Страницы: 10

Бренд: Magnetrol Страницы: 24

Бренд: Xenteq Страницы: 22

Бренд: Ultra Страницы: 20

3C63100-AC-C - PathBuilder S600...

Бренд: 3Com Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды