D-Link DGS-1510/ME Series, Справочное руководство

Страница: 88 / 654

DGS-1510/ME Series Metro Ethernet Switch CLI Reference Guide
84
cir - Specifies the Committed Information Rate. The unit is in Kbps. CIR should always be equal or less than
PIR.
<value 1-10485760> - Enter the CIR value here. This value must be between 1 and 10485760.
cbs - (Optional) Specifies the Committed Burst Size. The unit is Kbytes. That is to say, 1 means 1Kbytes. This
parameter is an optional parameter. The default value is 4*1024.
<value 1-262144> - Enter the CBS value here. This value must be between 1 and 262144.
pir - Specifies the “Peak Information Rate”. The unit is in Kbps. PIR should always be equal to or greater than
CIR.
<value 1-10485760> - Enter the peak information rate value here. This value must be between 1 and
10485760.
pbs - (Optional) Specifies the “Peak Burst Size”. The unit is in Kbytes. This parameter is an optional
parameter. The default value is 4*1024.
<value 1-262144> - Enter the peak burst size value here. This value must be between 1 and 262144.
color_blind - (Optional) Specifies the meter mode as color-blind. The default is color-blind mode.
color_aware - (Optional) Specifies the meter mode as color-aware. The final color of the packet is determined
by the initial color of the packet and the metering result.
conform - (Optional) Specifies the action when a packet is mapped to the “green” color.
permit - Specifies to permit the packet.
replace_dscp - Specifies to change the DSCP of the packet.
<value 0-63> - Enter the replace DSCP value here. This value must be between 0 and 63.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The resource may
be limited so that a counter cannot be turned on. Counters will be cleared when the function is disabled.
enable - Specifies that the ACL counter option will be enabled.
disable - Specifies that the ACL counter option will be disabled.
exceed - Specifies the action when a packet is mapped to the “yellow” color.
permit - Specifies to permit the packet.
replace_dscp - (Optional) Specifies to change the DSCP of the packet.
<value 0-63> - Enter the replace DSCP value here. This value must be between 0 and 63.
drop - Specifies to drop the packet.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The resource may
be limited so that a counter cannot be turned on. Counters will be cleared when the function is disabled.
enable - Specifies that the ACL counter option will be enabled.
disable - Specifies that the ACL counter option will be disabled.
violate - Specifies the action when a packet is mapped to the “red” color.
permit - Specifies to permit the packet.
replace_dscp - (Optional) Specifies to change the DSCP of the packet.
<value 0-63> - Enter the replace DSCP value here. This value must be between 0 and 63.
drop - Specifies to drop the packet.
counter - (Optional) Specifies the ACL counter. This is optional. The default is “disable”. The resource may
be limited so that a counter cannot be turned on. Counters will be cleared when the function is disabled.
enable - Specifies that the ACL counter option will be enabled.
disable - Specifies that the ACL counter option will be disabled.
sr_tcm - Specifies “single rate three color mode”.
cir - Specifies the Committed Information Rate. The unit is Kbps.
<value 0- 10485760> - Enter the CIR value here. This value must be between 0 and 10485760.
cbs - Specifies the Committed Burst Size. The unit is Kbytes.
<value 1-262144> - Enter the CBS value here. This value must be between 1 and 262144.
ebs - Specifies the Excess Burst Size. The unit is Kbytes.
<value 1-262144> - Enter the EBS value here. This value must be between 1 and 262144.
color_blind - (Optional) Specifies the meter mode as color-blind. The default is color-blind mode.
color_aware - (Optional) Specifies the meter mode as color-aware. The final color of the packet is determined
by the initial color of the packet and the metering result.