manualshive.com logo in svg

Cypress PSoC CY8C23533, Техническое справочное руководство

Поделиться
Скачать
Cypress PSoC CY8C23533 Скачать руководство пользователя страница 66

66

Document # 001-20559 Rev. *D

Interrupt Controller

5.3.2.2

INT_MSK0 Register

Bit 7: VC3.  

This bit allows posted VC3 interrupts to be

read, masked, or set.

Bit 6: Sleep.  

This bit allows posted sleep interrupts to be

read, masked, or set.

Bit 5: GPIO.  

This bit allows posted GPIO interrupts to be

read, masked, or set.

Bit 4: SAR8 ADC.  

This bit allows posted SAR8 ADC inter-

rupts to be read, masked, or set.

Bit 3: Analog 2.  

This bit allows posted analog column 2

interrupts to be read, masked, or set.

Bit 2: Analog 1.  

This bit allows posted analog column 1

interrupts to be read, masked, or set.

Bit 1: Analog 0.  

This bit allows posted analog column 0

interrupts to be read, masked, or set.

Bit 0: V Monitor.  

This bit allows posted V monitor inter-

rupts to be read, masked, or set.

For additional information, refer to the 

INT_MSK0 register

on page 104

.

5.3.2.3

INT_MSK1 Register

Bit 3: DCB03.  

This bit allows posted DCB03 interrupts to

be read, masked, or set for row 0 block 3.

Bit 2: DCB02.  

This bit allows posted DCB02 interrupts to

be read, masked, or set for row 0 block 2.

Bit 1: DBB01.  

This bit allows posted DBB01 interrupts to

be read, masked, or set for row 0 block 1.

Bit 0: DBB00.  

This bit allows posted DBB00 interrupts to

be read, masked, or set for row 0 block 0.

For additional information, refer to the 

INT_MSK1 register

on page 105

.

5.3.3

INT_VC Register 

The Interrupt Vector Clear Register (INT_VC) returns the
next pending interrupt and clears all pending interrupts
when written.

Bits 7 to 0: Pending Interrupt[7:0].  

When the register is

read, the 

least significant byte (LSB)

, of the highest prior-

ity pending interrupt, is returned. For example, if the GPIO
and I2C interrupts are pending and the INT_VC register was
read, the value 1Ch is be read. However, if no interrupts are
pending, the value 00h is returned. This is the reset vector in
the interrupt table; however, reading 00h from the INT_VC
register should not be considered an indication that a sys-
tem reset is pending. Rather, reading 00h from the INT_VC
register simply indicates that there are no pending inter-
rupts. 

The highest priority interrupt, indicated by the value returned
by a read of the INT_VC register, is removed from the list of
pending interrupts when the M8C services an interrupt.

Reading the INT_VC register has limited usefulness. If inter-
rupts are enabled, a read to the INT_VC register does not
determine that an interrupt was pending before the interrupt
was actually taken. However, while in an interrupt, a user
may wish to read the INT_VC register to see what the next
interrupt is. When the INT_VC register is written, with any
value, all pending and posted interrupts are cleared by
asserting the clear line for each interrupt.

For additional information, refer to the 

INT_VC register on

page 106

.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,E2h

INT_VC

Pending Interrupt[7:0]

RC : 00

LEGEND

C Clearable register or bits.

Содержание PSoC CY8C23533



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды