manualshive.com logo in svg

Cypress PSoC CY8C23533, Техническое справочное руководство

Cypress PSoC CY8C23533 - микроконтроллер с широкими возможностями программирования. Получите бесплатно Техническое Руководство по управлению, загрузите его с manualshive.com. Эта детальная инструкция поможет вам максимально использовать функциональность этого продукта для ваших проектов.

Поделиться
Скачать
background image

18

Document # 001-20559 Rev. *D

Section A:  Overview

Top-Level Architecture 

The PSoC block diagram on the next page illustrates the
top-level architecture of the PSoC device. Each major
grouping in the diagram is covered in this manual in its own
section: PSoC Core, Digital System, Analog System, and
the System Resources. Banding these four main areas
together is the communication network of the system 

bus

.

PSoC Core

The PSoC Core is a powerful engine that supports a rich
instruction set. It encompasses the 

SRAM

 for data storage,

an 

interrupt

 controller for easy program execution to new

addresses, sleep and watchdog timers, and multiple 

clock

sources that include the phase locked loop (PLL), IMO
(internal main oscillator), ILO (internal low speed oscillator),
and ECO (32.768 kHz external crystal oscillator) for preci-
sion, programmable clocking. The clocks, together with pro-
grammable clock dividers (as a System Resource), provide
the flexibility to integrate almost any timing requirement into
the PSoC device.

The CPU core, called the M8C, is a powerful processor with
speeds up to 24 MHz. The M8C is a four MIPS 8-

bit

 Har-

vard architecture microprocessor. Within the CPU core are
the 

SROM

 and 

Flash

 memory components that provide

flexible programming. 

PSoC GPIOs provide connection to the CPU, digital and
analog resources of the device. Each pin’s drive mode may
be selected from eight options, allowing great flexibility in
external interfacing. Every pin also has the capability to gen-
erate a system interrupt on high level, low level, and change
from last read. 

Digital System

The Digital System is composed of digital rows in a block
array, and the Global, Array, and Row Digital Interconnects
(GDI, ADI, and RDI, respectively).The digital system block is
composed of 4 digital PSoC blocks. Each block is an 8-bit
resource that can be used alone or combined with other
blocks to form 8-, 16-, 24-, and 32-bit peripherals, which are
called user modules.

The digital blocks can be connected to any GPIO through a
series of global buses that can route any signal to any pin.
The buses also allow for signal multiplexing and for perform-
ing logic operations. This configurability frees your designs
from the constraints of a fixed peripheral controller.

Analog System

The Analog System is composed of analog columns in a
block array, analog references, analog 

input

 muxing, and

analog drivers. The analog system block is composed of 6
configurable blocks, each comprised of an opamp circuit
allowing the creation of complex analog signal flows. 

Analog blocks are arranged in a column of three, which
includes one CT (Continuous Time) and two SC (Switched
Capacitor) blocks. The Analog Column 0 contains the SAR8
ADC block rather than the standard SC blocks.

System Resources

The System Resources provide additional PSoC capability.
These system resources include:

■

Digital clocks to increase the flexibility of the PSoC 
device.

■

One multiply accumulate (MAC) provides a fast 8-bit 
multiplier with 32-bit accumulate to assist in both general 
math as well as digital filters.

■

The decimator provides a custom hardware filter for digi-
tal 

signal

 processing applications, including the creation 

of Delta Sigma ADCs.

■

I2C

 functionality for implementing either I2C slave or 

master.

■

Low Voltage Detection (LVD) interrupts can signal the 
application of falling voltage levels, while the advanced 
POR (Power On Reset) circuit eliminates the need for a 
system supervisor.

■

An internal voltage reference that provides an absolute 
value of 1.3 V to a variety of PSoC subsystems.

■

Various system resets supported by the M8C.

Содержание PSoC CY8C23533



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PSoC CY8C23533

IEI Technology HYPER-AL Quick Installation Manual preview
HYPER-AL
Бренд: IEI Technology Страницы: 13
Asus Aaeon UP-CORE Quick Installation Manual preview
Aaeon UP-CORE
Бренд: Asus Страницы: 14
Asus Tinker Edge T Getting Started preview
Tinker Edge T
Бренд: Asus Страницы: 12
Asus Aaeon RICO-3288 User Manual preview
Aaeon RICO-3288
Бренд: Asus Страницы: 36
Asus AAEON PICO-APL4 User Manual preview
AAEON PICO-APL4
Бренд: Asus Страницы: 90
Asus E393S-IM-AA User Manual preview
E393S-IM-AA
Бренд: Asus Страницы: 102
Asus AAEON PICO-EHL4 User Manual preview
AAEON PICO-EHL4
Бренд: Asus Страницы: 108
Asus AAEON PICO-KBU4 User Manual preview
AAEON PICO-KBU4
Бренд: Asus Страницы: 93
Texas Instruments TMS320DM335 User Manual preview
TMS320DM335
Бренд: Texas Instruments Страницы: 172
Biostar BIH11-AHB User Manual preview
BIH11-AHB
Бренд: Biostar Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды