background image

Aerial work platform 

B-LIFT 18 HV

5

COD. UM0287_GB | REV. 00 | ED: 09/18

Chapter 01

GB

GENERAL INFORMATION

This manual may not in any way replace the speciic technical preparation which operators 

must have previously undergone on similar machines or else which they must undergo 

under the supervision of qualiied personnel.

This manual is written for the persons responsible for performing the following operations on the 
machine:

• 

Transport and handling

• 

Use

• 

Adjustments

• 

Cleaning

• 

Maintenance

• 

Demolition and disposal

PROHIBITED
It is prohibited for persons to perform operations or work which falls outside 

their speciic areas of expertise and responsibilities.

1.3.7 

Conservation

This manual is an integral part of the machine and should be stored with care in the cab 
dashboard so it can be readily consulted at any moment.
The manual must always accompany the machine along with the CE declaration of conformity, 
the check register and any other documents relating to the machine, including in the event 
that it is sold, up until such time as it is removed from service or disposed of.
Make a note of the fabrication number on the cover in order to easily identify the manual.
If the manual is lost or has deteriorated, request a new copy from the manufacturer, quoting 
the code on the cover or the machine’s factory number.

PROHIBITED

Do not remove, tear out or make arbitrary modiications to any parts of this 

document.

1.3.8 

Conidentiality

The technical information (text, drawings and illustrations) contained in this manual are property of 

CTE S.p.A.

 and should be considered conidential.

It is strictly prohibited to disclose, reproduce or translate this document, in whole or in part, without 
written authorisation from 

CTE S.p.A.

Содержание B-LIFT 18 HV

















































































































































Отзывы: