CTC Union FRM220-100AS-1 Скачать руководство пользователя страница 73

Страница: 73 / 83

CHAPTER 4

PROVISIONING VIA WEB BASED MANAGEMENT

4.5.5 Static 802.1Q VLAN

Please refer to Chapter 3.6.1 Static 802.1Q VLAN for a description of and operation of Static

VLAN feature in this device and to 3.6.5 Class of Service for Class of Service settings.

Some Tagging definitions:

Tagged

: This means that packets that egress the assigned port will have the packets tagged with

the VID assigned to that port.

Untagged

: This means that any packets that egress the assigned port will have all tag information

removed.

Non-member

: When a port is not a member of a VID, packets tagged with that VID will not be

allowed to egress that port. (i.e. they will be dropped)

Unmodified

: This means that packets exiting the assigned port will still have the same tag as when

they entered any other port of the switch, i.e., unmodified

Содержание FRM220-100AS-1




















































































Результаты поиска

Содержание FRM220-100AS-1

Отзывы:

Бренды по названию

Популярные бренды

CTC Union FRM220-100AS-1, Руководство пользователя

Результаты поиска

Содержание FRM220-100AS-1

Отзывы:

Бренды по названию

Популярные бренды