CTC Union FRM220-100AS-1 Скачать руководство пользователя страница 68

Страница: 68 / 83

CHAPTER 4

PROVISIONING VIA WEB BASED MANAGEMENT

Refresh Status

: Updates the display with current information.

Remote H/W Reset

: Provides ability to reset device at remote side, if the device is configured to so

allow.

4.5.2 UTP

This window tab will show current status and provide settings for the UTP port.

Parameters

Port Active

: When disabled, this port will be completely inactive.

Negotiation

: This sets up the UTP port for either auto-negotiation per 802.3u or sets manual

configuration mode.

Speed:

Select the UTP port speed. Port speed can be either 10M or 100M.

Duplex:

Select the duplex mode. This could be either half or full duplex.

Ingress Rate Limit

: Enter the ingress rate limit. The allowed range is between 64k and 990M.

Egress Rate Limit

: Enter the egress rate limit. The allowed range is between 64k and 990M.

Содержание FRM220-100AS-1




















































































Результаты поиска

Содержание FRM220-100AS-1

Отзывы:

Бренды по названию

Популярные бренды

CTC Union FRM220-100AS-1, Руководство пользователя

Результаты поиска

Содержание FRM220-100AS-1

Отзывы:

Бренды по названию

Популярные бренды