COSMOGAS POOLDENS 100T, Инструкция по установке, эксплуатации и обслуживанию

Страница: 40 / 96

40 POOLDENS
COSMOGAS
13 - INSTALLATION - External cover
13.1 - Installation of external cover for
models 34T - 60T - 70T - 100T - 115T - 140T
WARNING :
the small parts of this kit will have the following references:
- Screw 6x20 will be shown by “A”;
- Screw 4x10 will be shown by “B”;
- Screw 4x25 will be shown by “C”;
- Screw 4x20 will be shown by “D”.
WARNING :
Overtightening of screws “C” may lead to deformation of
the panel on which they are applied.
For installation of the external cover, proceed as follows:
1.- Loosen, with the relevant spanner, the appliance’s
adjustable feet “T” (figure 13-1), insert rod “H” and retighten
the adjustable feet “T” (figures 13-2 and 13-3). Repeat the
same procedure on the opposite side.
2.- Remove the appliance’s upper and lower front covers “F”
and the upper cover “U”, as shown in figure 13-4.
3.- Insert the lower framework J” (figure 13-5) and attach it to
rod “H” with the relative screws “A” in correspondence with
the holes that are present (figure 13-6).
4.- Replace the appliance’s upper and lower front covers “F”
(figure 13-7). Then adjust the adjustable feet “I” of the lower
framework “J” to regulate the appliance’s stability on the
surface it is installed on (figure 13-8).
5.- Insert the four tubes “K” in correspondence with the pins
present on the lower framework “J” using a rubber mallet
(figures 13-9 and 13-10).
6.- Insert the upper framework “G” of the external cover using
a rubber mallet (figure 13-11).
7.- Insert the upper fixing rods “Q” (figures 13-12 and 13-13).
Then put in screw “A” with nut “E” for fastening the rods to
the appliance (figure 13-14) and screw “B” for fastening the
rods to the framework of the external cover (figure 13-15).
8.- Attach the cover AB , using screws “C”, to the framework
of the external cover, as shown in figure 13-16.
9.- Put on the covers AA and AC in the direction shown in
figure 13-19 and fasten them to the structure with screws
“C”; first removing the pre-cut discs present (figures 13-17
and 13-18). It is also possible, depending on the type of
electrical and condensate removal system in the place the
appliance is installed, to remove if necessary the pre-cut
sections “X” and “Y” on the metal sheet AC shown in
figure 13-19.
10.- Fix the two anti-rain grills “R” and the metal plates “S” to
the covers previously assembled; using screws “B” (figure
13-20).
11.- Fix the metal plates “V”, with screws “B”, onto the back
of the external cover, as shown in figure 13-21.
12.- Put on the side covers AD , attaching them to the structure
with screws “C” (figure 13-22).
13.- Position the top cover AE as shown in figure 13-23 and
fix it to the upper framework “G” using screws “B” (figure
13-24), in correspondence with the holes present.
14.- Attach, using screws “D”, the shelter for the electrical
connections “L”, for the intake “M” and for the outlet
“N” (or “P”) to the top cover (figures 13-25 and 13-26);
remembering to insert gaskets “O” and “W” as shown in
figure 13-25.
WARNING :
- If you have a flue gas outlet 110 mm in diameter, use
outlet covers “N” in figure 13-25.
- If you have a flue gas outlet 80 mm in diameter, use
outlet covers “P” in figure 13-25.
15.- Put on the front cover AN as shown in figure 13-27 and
13-28. Attach it to the structure by tightening locks “Z” with
a flat-head screwdriver (figure 13-29).
16.- Finally, attach metal sheets AR and AS , using screws
“B”, to the lower framework “J”; as shown in figures 13-30
and 13-31.